Click image to view full size image
Hoozhu V13 Diving Video Light
Product Description
1. Model: V13
2. Name: Diving video light (LED lamp for Diving Video)
3. LED: 4x CREE XML U2(white, 2600 lm), 2x CREE XP-E-NB R2, 2x CREE XP-E- Q4 G2,2x UV,2x purple light
4. Five colors of light: White:2600 lm,Red:200 lm,Green:200 lm,UV:6W,Purple: 6W
5. Switch 1: White: High,Low,Strobe,Close.
6. Switch 2: Red,Purple,Green,UV
7. BurnTime: High: 1.0 hrs, Low: 5.0 hrs, Strobe: 5.0 hrs,
8. Waterproof: 120 meters
9. Material: Aeronautical aluminum
10. Clolor: Black/Blue
11. Treatment: Hard-anodizing type III
12. Lens: 4mm clear PC
13. Beam Angle: 120 degrees
14. Voltage: 2.8V to 4.5V.
15. Battery: 1x 32650 Li-ion battery
16. Sizes: 143(L)x41(body dia.)x50(head dia.)mm
17. Weight: 345 g (w/o battery)
NOTES:
1. The Diving Light with special fixture.It would be damaged if disassembled at your own discretion.
2. Pl inspect the O-rings carefully every time you finished diving and change the broken O-rings when necessary.
3. After every diving,pl clean the flashlight body with fresh water,and store it properly after full dried.
BATTERY INSTALLATION
1. Remove the tail by turning counter-clockwise.
2. Remove used batteries and replace with fresh batteries as shown by the polarity stickers.
3. Mount the tail by turning clockwise.DO NOT ACTIVATE IT YET.
BATTERY CHARGING
1. Plug the charger in the wall power socket, the indicator light is green in the free-load status.
2. Put the battery in the slot of the charger.
3. The indicator light is red if the batter is not fully charged; It will turn green after fully charged.
4.Take out the fully charged battery and use them in the diving light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise damaged O-ring or mating lens surface as this can cause the light to flood under pressure. Remove any salt deposits, sand, dirt, or other foreign matter from the O-ring sealing surfaces.
KEEP THE THREADS, O-RING GROOVE LUBRICATED WITH SILICONE GREASE.
CAUTION
If the light is not to be used for sometime,remove the batteries to prevent possible leakage or corrosion.Pl remove the batteries during transportation to prevent it from incorrect operation
WARRANTY: One Year
Product Description
1. Model: V13
2. Name: Diving video light (LED lamp for Diving Video)
3. LED: 4x CREE XML U2(white, 2600 lm), 2x CREE XP-E-NB R2, 2x CREE XP-E- Q4 G2,2x UV,2x purple light
4. Five colors of light: White:2600 lm,Red:200 lm,Green:200 lm,UV:6W,Purple: 6W
5. Switch 1: White: High,Low,Strobe,Close.
6. Switch 2: Red,Purple,Green,UV
7. BurnTime: High: 1.0 hrs, Low: 5.0 hrs, Strobe: 5.0 hrs,
8. Waterproof: 120 meters
9. Material: Aeronautical aluminum
10. Clolor: Black/Blue
11. Treatment: Hard-anodizing type III
12. Lens: 4mm clear PC
13. Beam Angle: 120 degrees
14. Voltage: 2.8V to 4.5V.
15. Battery: 1x 32650 Li-ion battery
16. Sizes: 143(L)x41(body dia.)x50(head dia.)mm
17. Weight: 345 g (w/o battery)
NOTES:
1. The Diving Light with special fixture.It would be damaged if disassembled at your own discretion.
2. Pl inspect the O-rings carefully every time you finished diving and change the broken O-rings when necessary.
3. After every diving,pl clean the flashlight body with fresh water,and store it properly after full dried.
BATTERY INSTALLATION
1. Remove the tail by turning counter-clockwise.
2. Remove used batteries and replace with fresh batteries as shown by the polarity stickers.
3. Mount the tail by turning clockwise.DO NOT ACTIVATE IT YET.
BATTERY CHARGING
1. Plug the charger in the wall power socket, the indicator light is green in the free-load status.
2. Put the battery in the slot of the charger.
3. The indicator light is red if the batter is not fully charged; It will turn green after fully charged.
4.Take out the fully charged battery and use them in the diving light.
SCUBA DIVING APPLICATION
Check closely for cuts, scratches, or an otherwise damaged O-ring or mating lens surface as this can cause the light to flood under pressure. Remove any salt deposits, sand, dirt, or other foreign matter from the O-ring sealing surfaces.
KEEP THE THREADS, O-RING GROOVE LUBRICATED WITH SILICONE GREASE.
CAUTION
If the light is not to be used for sometime,remove the batteries to prevent possible leakage or corrosion.Pl remove the batteries during transportation to prevent it from incorrect operation
WARRANTY: One Year